What Does a 35 mm Fanless PC Need Behind a Kiosk Screen?

BVS GW-X 35 mm fanless industrial mini PC mounted inside a kiosk service compartment

INDUSTRIAL MINI PCS

A computer behind a kiosk screen gets 35 mm of depth, no airflow and whatever voltage the kiosk already carries. Those three numbers decide the model.

Depth is the number that fails first

A kiosk is designed around a screen, a payment device and a cavity sized for a compact embedded system, and that cavity is usually the last thing anyone measures. A unit of 316 x 198 x 35 mm fits where a 60 mm box does not, but the 35 mm is the chassis, not the installation: an HDMI plug and a right-angle DC connector each add 25 to 40 mm behind the case. Take the depth of the cavity, subtract the connector stack, and only then compare it with the chassis. On this model the wall-mount ears run along both long sides, so the case can hang on a backplate instead of sitting on a shelf that eats another 200 mm.

Passive cooling in a space nobody opens

Behind a screen there is no fan to clean and no filter to change, which is the reason to specify a fanless embedded computer in the first place. The aluminium housing on this unit is cast with fins on the mounting face, so the case is the heatsink and the heat leaves through the backplate into the kiosk frame. What that rules out is a closed plywood box with the vents taped over: the same 35 mm that makes it fit also means the case has to be able to breathe through its own surface. Leave the fin face clear, keep 20 mm of air on the fin side, and do not wrap the unit in foam packing tape during installation.

◆  Mount the fin face towards the open side of the cavity, not flat against a wooden panel.

◆  Keep the two antenna bases clear of metal; a Wi-Fi antenna pressed against a steel backplate loses more range than a firmware change can recover.

◆  Expect the cavity to run 8 to 12 degrees warmer than the room; a fanless unit rated for the room will sit at the top of its range in August.

◆  Leave the cable gland at the bottom, so dust falls away from the connectors rather than into them.

Two LAN and two COM are the ports that pin the model

Most kiosk failures are network failures, and a second LAN port is the cheapest fix: one port faces the payment terminal or the machine controller, the other faces the building network, and the two never share a broadcast domain. Two COM ports matter for the same practical reason, because a bill acceptor, a scale or an older controller still speaks RS232 or RS485 while the screen speaks IP. This unit carries two LAN, two USB, HDMI and VGA, two serial ports, a microphone input and a line output, which is the full set a self-ordering or payment kiosk normally needs.

Four numbers that decide the fit

Item What the model gives What it decides on site
Chassis 316 x 198 x 35 mm, aluminium Whether it fits the cavity with the connector stack
Mounting Wall-mount ears on both sides Hanging on a backplate instead of a shelf
Network 2 x LAN, Wi-Fi with 2 antennas Separating the payment side from the building side
Power 12 to 19 V DC input Whether the kiosk PSU can drive it directly

Why a wide input range beats a fixed adapter

A kiosk usually has one power supply, sized for the screen and the peripherals. A computer that only accepts 12 V forces a second adapter, a second socket and a second point of failure inside a cabinet nobody opens. A 12 to 19 V input can run from the rail that is already there, and it also survives the voltage drop of a long DC run to a floor-standing unit. On the compute side the i5 12th gen build with 16 GB of DDR4 and a 512 GB SSD is more than a browser needs; it is there so the same unit can also drive a 4K screen and keep a content cache, and so a buyer who wants one platform across a kiosk range does not need a second design.

Questions buyers ask before the first sample

Can it drive two screens on a kiosk?

Yes, one HDMI and one VGA output are fitted. That covers a main screen plus a customer-facing second display, which is the usual arrangement at a payment counter.

Does it need a fan kit in a warm mall?

No. The housing is the heatsink, and adding a fan to a fanless chassis helps less than clearing the fin face and leaving the cavity open at the top and bottom.

Is the unit available in OEM colours and branding?

Yes. oem odm mini pc projects normally cover the housing colour, the logo and the boot image, which is what a kiosk builder needs when the box is visible through a service hatch.

Check the range

The models discussed here are listed in our collections, from industrial mini PCs and fanless embedded computers to the payment kiosks they are built into, with port maps and dimensions on each product page.

◆  industrial mini PCs

◆  payment and self-ordering kiosks

◆  interactive monitors

If you need a drawing or a port list for a specific model, send the requirement and we will reply with the document rather than a brochure.

RELATED ARTICLES